Search for answers or browse our knowledge base.
MDM-100(FMC225) / MDM-101(MCX301) Manual Programing
This article will go over the steps of manually programing the FMC225 & MCX301 Modems, along with the programing using a Config file. Note: You’ll need the Morey Configurator and the Telematics Configuration Tool.
FMC-225 Hardware Setup
Step 1) Open the FMC-225 case and remove the PCB. Please Note: there are 2 clips that hold the PCB to the case. These clips are located on the opposite side of the 12-pin connector.
Step 2) Carefully remove the battery wire from the tape without pulling up the battery. Connect the Battery to the PCB.
Step 3) Remove the clear plastic from the SIM slot. Insert the SIM card into the SIM Slot 1.
Step 4) Carefully snap the PCB back into the case.
Step 5) Using the custom cable for the modem, connect the power and ground to the cable. Plug the modem into the custom cable using the Teltonika 12-pin connector.
Step 6) Using a USB to Mini USB cable, connect the FMC-225 to the computer.
FMC-225 Software Configuration (Manual Input)
Step 1) Open the Telematics Configuration Tool.
Step 2) In the ‘Looking for devices, they will be listed here if detected‘ section, the FMC225 will appear here. Click the blue Configure button. Note: if device is not listed, disconnect the USB and reconnect.
Step 3) On the left side, select the Mobile Network option. Under SIM1, set the APN to data.mono
Step 4) Still in the Mobile Network settings, scroll down to the Primary Server Setting section. Set the Domain & Port settings accordingly. Leave Data Protocol as TCP
Doman: ch1180915.flespi.gw
port: 30156
Step 5) On the left menu, select the System. In the Movement Settings, set Movement Source to Ignition & Accelerometer.
Step 6) Scroll down to the Power Saving Settings. Using the toggle switch, disable the setting.
Step 7) Scroll down to the GNSS Settings. Set the GNSS Source to GPS, GLONASS, & Galileo.
Step 8) On the left menu, select Tracking Settings. In the Records Settings, set the Saving / Sending Mode to Always.
Step 9) On the left menu, select Accessories. Select the Serial Communication Settings button. Using the toggle switch, enable the Serial Communication Settings.
Step 10) In the RS232 Settings, set the Mode and Baudrate to the following:
Mode: TCP Binary Buffered
Baudrate: 38400
Step 11) Staying in the Serial Communication Settings, scroll down to the TCP Binary Mode Setting. Set Prefix 1 to 136
Step 12) In the bottom right corner, click the Save to Device button.
MCX-301 Hardware Setup
Step 1) Open the MCX-301 case and remove the PCB. Please Note: there are 2 clips that hold the PCB to the case. These clips are located on the opposite side of the 20-pin connector.
Step 2) Carefully remove the battery wire from the tape without pulling up the battery. Connect the Battery to the PCB.
Step 3) Remove the clear plastic from the SIM slot. Insert the SIM card into the SIM Slot 1.
Step 4) Carefully snap the PCB back into the case.
Step 5) Using the custom cable for the modem, connect the power and ground to the cable. Plug the modem into the custom cable using the Teltonika 20-pin connector.
Step 6) Using a USB to Mini USB cable, connect the FMC-225 to the computer.
MCX-301 Software Configuration (Manual Input)
Step 1) Open the Morey software.
Step 2) Once open, you’ll see the software searching for the connected device. Once the device is detected, it’ll appear under the ‘Create new configuration‘ and ‘Open configuration file‘ buttons. Click on the MCX-301 in the Base section. Note: if device is not listed, disconnect the USB from the PC and reconnect.
Step 3) On the left side, select the System option.
Step 4) Under the Sleep Settings, select the Disable option.
Step 5) Under the Records Settings, set the Saving / Sending Mode to Always
Step 6) Within the System Settings section, under the GNSS Source, make sure GPS, GlONASS, & GALILEO are selected.
Step 7) Under Protocol Settings, verify it’s set to Codec 8 Extended
Step 8) Under IO Global Settings, verify IO Send Mode is set to Dont Send.
Step 9) On the left menu, select GPRS.
Step 10) Under the SIM1 GPRS Settings and SIM2 GPRS Settings, set the APN to data.mono
Step 11) Under the Service #1 Settings, set the Doman and Port to the following:
Doman: ch1180915.flespi.gw
port: 30156
Step 12) On the left menu, select RS232\RS485
Step 13) Under the RS232 Settings, set the Mode, Baudrate, and Start Byte to the following:
Mode: TCP Binary Buffered and set
Baudrate: 38400
Start Byte: 136
Step 14) Now that we’ve set all the required parameters, click the Save to Device button along the top of the configuration software.
Configure Modem with a Configuration File (FMC-225)
Step 1) Open the Telematics Configuration Tool.
Step 2) In the ‘Looking for devices, they will be listed here if detected‘ section, the FMC225 will appear here. Click the blue Configure button. Note: if device is not listed, disconnect the USB and reconnect.
Step 3) In the left menu, select the Upload File (.cfg) button. A window will appear. Select the desired configuration file and click Open
Step 4) In the bottom right corner, click the Save to Device button.
Configure Modem with a Configuration File (MCX-301)
Step 1) Open the Morey Configuration Tool.
Step 2) Once open, you’ll see the software searching for the connected device. Once the device is detected, it’ll appear under the ‘Create new configuration‘ and ‘Open configuration file‘ buttons. Click on the MCX-301 in the Base section. Note: if device is not listed, disconnect the USB from the PC and reconnect.
Step 3) In the top menu, select the Load From File button. A window will appear. Select the desired configuration file and click Open
Step 4) In the top menu, click the Save to Device button.